Supports

Supports are used to hold a part so it doesn't displace when loads are applied to it. Use the Apply Support tool on the Loads icon to apply a support.

You can apply supports to a single point on the model, to an edge or a face, or at the center of a hole.



Apply a Support

Select the Apply Support tool, click on a feature, and click the support cone to edit it.

  1. Click the Apply Support tool on the Loads icon.


  2. Click on a point, edge, face, or hole.
    • Hold the Shift key as you click to create a concentrated point support.
    • Hold the Ctrl key to apply the support to multiple features on the same part.
  3. To allow translation in one or more directions for a particular support, click on a cone for that support. A transparent axis trident appears.


  4. Click on the arrows to toggle the locks on and off in those directions.
    A green arrow indicates that translation is allowed in that direction, while a gray arrow indicates that it is locked.


  5. Right-click and mouse through the check mark to exit, or double-right-click.
Tip:
  • You can edit individual supports to allow translation or rotation in one or more directions. Double-click on a support to enter editing mode.
  • A distributed support acts in a single direction across the extent of an edge or face. You can change whether a support is distributed or not in the Property Editor.
  • Once a support is created, you can move it away from the model to create a support at a distance by using the Move tool on the microdialog.
  • Use the Property Editor to change the name, connection type (rigid or flexible), and appearance of the support, and whether it rotates with the part.

Apply a Support to a Cylindrical Hole

Supports applied to a cylindrical hole are a special case, and have different properties from supports applied to a point, edge, or face.

  1. Click the Apply Support tool on the Loads icon.


  2. Click on the interior of a cylindrical hole.
    • Hold the Shift key as you click to create a concentrated point support.
    • Hold the Ctrl key to apply the support to multiple features.
  3. To allow translation or rotation, click on the red support cylinder.
    Transparent graphical handles appear.


  4. Click on the arrows to toggle the locks on and off in those directions.
    A green arrow indicates that translation or rotation is allowed in that direction, while a gray arrow indicates that it is locked.


  5. Right-click and mouse through the check mark to exit, or double-right-click.
Tip:
  • Use the Property Editor to change the name, connection type (rigid or flexible), and appearance of the support, and whether it rotates with the part.
  • A distributed support acts in a single direction across the extent of an edge or face. You can change whether a support is distributed or not in the Property Editor.
  • You can enable optimization for cylindrical supports in the Property Editor.
  • You can change how connection stiffness is defined for cylindrical supports in the Property Editor.

Translate or Rotate Supports

When you create a support, translation is locked in all directions by default; but you can edit individual supports to allow translation in one or more directions.

  1. Double-click on a support to enter editing mode.
  2. Click the clear axis arrows to enable translation for that axis.
    A green arrow indicates translation or rotation is enabled.


Supports applied to a point, line, or face can translate in up to three directions.


Cylindrical supports applied to the center of a hole can translate or rotate.


Supports applied to a point can translate or rotate in three directions.

Place Supports at a Distance

Move a support away from the model to create a support at a distance.

  1. Double-click on a support to enter editing mode.
  2. Use the Move tool on the microdialog to translate the support.
    When the support is moved away, connectors are automatically created.
    Note: You can also apply a support to a point in space and then use the Connect Supports tool on the microdialog to manually create connectors.


Microdialog Options

Double-click a support to enter editing mode, which opens the Support microdialog.

Use the drop-down menu to select which type of feature to apply the support to, such as a point or face. When using the SimSolid solver there are additional options for Fixed, Sliding, and Hinged. Fixed and sliding options can be applied to holes or surfaces, while the hinged option can only be applied to holes
Create connectors to supports that have been moved away from the model.
Translate or rotate the support using the Move tool. Use to place a support at a distance.
Align the support normal (perpendicular) to the face.
Align the support to the global axes.

Mouse Controls and Keyboard Shortcuts

Ctrl Apply the support to multiple features on the same part.
Shift Create a concentrated support at a point on an edge, face, or hole.
Right-click and mouse through the check mark to exit, or double-right-click. Exit the tool.