CRASH-2200: Pedestrian Head Impact Simulation

The goal of this tutorial is to see how head impact simulation following the pedestrian safety regulation EuroNCAP can be defined using the Pedestrian Impact tool starting from a full vehicle model.

Pedestrian Impact automates the process with minimal input from you, therefore reducing the deck generation lead time with less human error.


Figure 1.

Model Description

The vehicle model used in this tutorial is based on the free Toyota Yaris model, provided by the National Crash Analysis Center (NCAC).

The original LS-DYNA model has been converted and validated with Radioss. The files needed for this tutorial are located in the pedestrian_impact.zip file. Copy these files into a local directory before proceeding with this tutorial.


Figure 2.

Load the Radioss User Profile

  1. From the Start menu, select Engineering Solutions > Crash (HyperMesh) or click on the Standard toolbar.
  2. Select Crash > RADIOSS.
  3. Click OK.

Load the Vehicle Model

  1. From the menu bar, click File > Import > Solver Deck.
  2. Click the icon to browse and select the vehicle input deck Toyota_Yaris_0000.rad file located in the Vehicle folder.
  3. Click Import.
    The model loads into the graphics area.

Open the Pedestrian Impact Tool

From the menu bar, click Safety > Pedestrian Impact.

Vehicle Marking

  1. In the Vehicle Marking tab, select the inputs for the regulation. For Regulation select EuroNCAP 8.4 and for Impactor select Headform.
  2. In the Parts selection section, select the different components needed for the marking process, as shown in the image below.


    Figure 3. Vehicle Outer Surfaces
    1. For Vehicle Outer select the Hood, Windshield, A-Pillars, Leaf Cover and headlamps components.
    2. For each single group of components (Hood, Windshield, A-Pillars, Leaf Cover), select the corresponding components.
  3. In the Vehicle Inclination section, set the definition of the Ground. For Ground Type select Flat. For Base node for Z enter .0.0.
  4. Click Ground plane to see the ground position.


    Figure 4.
  5. Click Mark to start the marking process.
    Figure 5.


Export Solver Decks for all Impact Points

Use the Positioning tab to perform the export of the solver decks for all headform impact points.

  1. Select and import the headform input deck.
    1. Click the Adult Headform icon and select the adult headform input deck Rigid_Adult_Headform_0000.rad located in the Impactors folder.
    2. Click the Child Headform icon and select the child headform input deck Rigid_Child_Headform_0000.rad located in the Impactors folder.
  2. Review the headform impactor positioning by selecting an impact point in the table, and click Preview.
  3. Click YES in the dialog that opens.
    Multiple impact points can be reviewed at the same time. The example below is for the C_O_O impact position.


    Figure 6.
  4. Activate the All checkbox in the Export filter section.
  5. In the Export options section, for the Adult and Child Headform, click the icon and select the respective master files master_euncap_A-Headform_0000.rad and master_euncap_C-Headform_0000.rad.
  6. For the Master out directory, click the icon and select the RUNS folder.
  7. Click Export to start the process to export the solver decks for all of the impact points.
    The following folders are created in the RUNS folder:


    Figure 7.
    The following folders are created in the Headform folder:


    Figure 8.
    In the Adult and Child folders, each of the impact points has its own folder with the corresponding master file, in which the impactor include file and the transformation cards are defined. For example, for the C_0_0 impact point, here is the data added by the tool in the master file:


    Figure 9.
    Each solver deck is ready to be solved by Radioss. Below is an example of the final C_0_0 impact point input deck:


    Figure 10.