Manufacturing Solutions

Numbers panel

»Click here to display Table of Contents« HyperForm > User's Guide > Panel Descriptions > HyperForm Panels:

Numbers panel
Numbers panel

User Profiles:

Incremental_RADIOSS

Incremental_LS-DYNA

RADIOSS One Step

Die Module

Use the Numbers panel to display the IDs of an entity.

HM_Panels_bmp00250

HM_Panels_bmp00251

Subpanels and Inputs

There are no subpanels on the Numbers panel. All inputs and command buttons are located on the main panel.

Panel Inputs

Input

Action

(entity selector)

Use the switch to pick the desired type of entity, then use the entity selector to select the desired entities--either by picking them in the graphics area, or using the extended entity selection menu.

When you select nodes or elems, click the switch to change the selection mode.

nodes

Select individual nodes.

faces_edges_nodes

faces

Select all of the nodes on 2D and 3D faces.

If there are discontinuities on a 2D face, then only the nodes inbetween the discontinuities will be selected.

faces_edges_faces_nodes

2D faces ext

Select all of the nodes on a 2D face that contain discontinuities.

faces_edges_2d_face_ext_nodes

loops

Select all of the nodes on continuous free edges that make a closed loop simultaneously, such as the perimeter of a hole.

Only valid for SHELL elements.

faces_edges_loops_nodes

free edges

Select all of the nodes on free edges of elements.

If there are discontinuities on an edge, then only the nodes on the free edges inbetween the discontinuities will be selected.

Only valid for SHELL elements.

faces_edges_free_edges_nodes

free edges ext

Select all of the nodes on free edges of elements that contain discontinuities.

Only valid for SHELL elements.

faces_edges_free_edges_ext_nodes

edges

Select all of the nodes on free edges or shared edges (butt joints, L/corner joints, and T-joints) of elements.

If there are discontinuities on an edge, then only the nodes on the edge inbetween the discontinuities will be selected.

Only valid for SHELL elements.

faces_edges_edges_nodes

edges ext

Select all of the nodes on free edges or shared edges (butt joints, L/corner joints, and T-joints) of elements that contain discontinuities.

Only valid for SHELL elements.

faces_edges_edges_ext_nodes

elems

Select individual elements, or select all of the elements contained by a component or on a surface.

faces_edges_entities

faces

Select all of the elements on 2D and 3D faces.

If there are discontinuities on a 2D face, then only the elements inbetween the discontinuities will be selected.

faces_edges_faces

2D faces ext

Select all of the elements on a 2D face that contain discontinuities.

faces_edges_2d_faces_ext

display

After numbers have been turned on for some entities, use this checkbox to toggle the display of all numbers on and off. (This differs from the on, off, and all off buttons in that it is only temporary and does not apply specifically to the entities selected.)

face angle / individual selection

Face angle

The face angle is the angle between the normal of facets that share an element edge. A facet can either be a shell element itself, or one of the faces of a solid element. The normal of triangular facets is that of the plane defined three corner vertices. Whereas, the normal of quadrilateral facets is calculated by taking the cross-product between its two diagonals. This special treatment for quadrilaterals is because a warped shape does not lie completely on a plane.

Only available when the entity selector is set to nodes or elems and the selection mode is set to faces, 2d faces ext, free edges, free edges ext, edges, or edges ext.

Individual Selection

Select individual elements on a face or select individual free/shared edges of elements.

Only available when the entity selector is set to nodes or elems and the selection mode is set to faces, free edges, or edges.

edge angle

Splits edges that belong to a given face.

When the edge angle is 180 degrees, edges are the continuous boundaries of faces. For smaller values, these same boundary edges are split wherever the angle between segments exceeds the specified value. A segment is the edge of a single element.

Only available when the entity selector is set to nodes and the selection mode is set to free edges, free edges ext, edges, or edges ext.

Command Buttons

The following action buttons appear:

Button	Action
on	Turn numbering on for the selected entities.
off	Turn numbering off for the selected entities. In this example, 4 and 5 are selected. Clicking off clears the selection (4 and 5).
all off	Turn numbering off for all entities. Unlike the display checkbox, this clears the numbers--meaning that you will need to reselect and click on if you wish to re-enable numbering.
return	Exit the panel.

How do I...

Display entity IDs

Turn off the display of IDs of specified data types

Turn off the display of all entity IDs

See also

An Alphabetical List of Panels