*barrierpositioner

Syntax

*barrierpositioner vehiclemark=<value> barriermark=<value> vehiclefrontaxis=<value> barrierfronaxis=<value> basenode=<value> inclinationnode=<value> ... ?<optionN>=<valueN>?

Type

HyperMesh Tcl Modify Command

Description

Positions the barrier according to various protocols with respect to given vehicle.

The model must contain vehicle and barrier parts, the vertical axis of these parts must be aligned with global positive z axis (0,0,1), the barrier model must be imported as an include file, and all barrier parts must be in the same include file.

Inputs

barrierfrontaxis={<x y z>}

The vector pointing toward the front of the barrier. It must be different from the global z axis. This is mandatory.

basenode={<x y z>}

The coordinates of the base node for ground. This is mandatory.

barrierfoamdistance=<value>

The frontal distance of the foam part of the barrier to be considered for calculating the bounding box of those nodes/coordinates for offset or overlap, default is 350.0.

barrierheightposition=<value>

The desired final distance between vehicle and barrier, defaults are given for each config below.

barrierimpactside=<value>

The default is 1 except for config=16. Valid values are:

1 - Left

2 - Right

barrierlateralangle=<value>

The lateral angle with which the barrier is rotated from expected barrier final axis. For front load case, barrier final axis is opposite of vehicle front axis. For side load case, it is lateral axis of vehicle and towards the vehicle, whereas it is front axis of vehicle for rear load case. Defaults are 0.0 except for config=14 the default is 15 degrees and for config=18 the default is 75 degrees.

barriermark=<value>

The ID of the mark of barrier components. Valid values are 1 and 2. This is mandatory.

barrieroverlappercent=<value>

The percentage overlap between car and vehicle for front load cases, defaults are given for each config below.

barriervehicleoffsetdist=<value>

The desired final distance between vehicle and barrier, default is 10.0.

config=<value>

The type of load case and regulation. Valid values are:

Config	Load Case	Regulation	Description	barrierheightposition	barrieroverlappercent	rpointoffset
11	Side	IIHS	Mobile Deformable Barrier (MDB)	379.0	-	-
12	Side	FMVSS-214D	Passenger Car	279.0	-	-
13	Side	FMVSS-214D	MPV	279.0	-	-
14	Side	Euro NCAP	MDB	300.0	-	250.0
15	Side	UN-R95	MDB	300.0	-	0.0
16	Side	J-NCAP	MDB	300.0	-	250.0
17	Side	C-NCAP	MDB	350.0	-	250.0
18	Side	Euro NCAP	Oblique Pole	102.0	-	-
31	Front	Euro NCAP	ODB	200.0	40.0	-
32	Front	Euro NCAP	MPDB	150.0	50.0	-
33	Front	IIHS	Small Overlap Rigid Barrier	0.0	25.0	-
34	Front	US NCAP	OMDB	200.0	15.0	-
51	Rear	FMVSS-301		229.0	70.0	-

inclinationnode={<x y z>}

The coordinates of the inclination node for ground. This is mandatory.

rpointoffset=<value>

The barrier distance from R Point of vehicle for side load cases or impact reference distance (IRD).

If the value is 0.0 for config 11, 12 or 13, then it will compute IRD. Defaults are given for each config above. Non-zero offset values take precedence and will be used as it is for positioning.

sidenode={<x y z>}

The coordinates of the side node for side load cases.

vehiclefrontaxis={<x y z>}

The vector pointing toward the front of the vehicle. It must be different from the global z axis. This is mandatory.

vehiclemark=<value>

The ID of the mark of vehicle components. Valid values are 1 and 2. This is mandatory.

wheelbasedistance=<value>

The wheelbase distance as the distance between front wheel axis and rear wheel axis, used for IRD calculations.

Examples

*createmark comps 1 "by include" $includeidvehicle
*createmark comps 2 "by include" $includeidbarrier
*barrierpositioner config=31 vehiclemark=1 barriermark=2 vehiclefrontaxis={1 0 0} barrierfrontaxis={-1 0 0} basenode={0.000087 913.163 0} inclinationnode={-4806.71 913.163 0} barrieroverlappercent=40.0 barrierheightposition=200.0 barrierfoamdistance=150.0 barriervehicleoffsetdist=10.0

*createmark comps 1 "by include" $includeidvehicle
*createmark comps 2 "by include" $includeidbarrier
*barrierpositioner config=34 vehiclemark=1 barriermark=2 vehiclefrontaxis={1 0 0} barrierfrontaxis={1 0 0} basenode={0.000087 913.163 0} inclinationnode={-4806.71 913.163 0} barrieroverlappercent=35.0 barrierheightposition=200.0 barrierlateralangle=15.0 barriervehicleoffsetdist=10.0 barrierfoamdistance=150.0

*createmark comps 1 "by include" $includeidvehicle
*createmark comps 2 "by include" $includeidbarrier
*barrierpositioner config=11 vehiclemark=1 barriermark=2 vehiclefrontaxis={1 0 0} barrierfrontaxis={0 1 0} basenode={0.000087 913.163 0} inclinationnode={-4806.71 913.163 0} sidenode={-777.060791 982.340820 330.154846} wheelbasedistance=2538.0 barrierimpactside=1 barrierheightposition=379.0 barrierfoamdistance=350.0 barriervehicleoffsetdist=10.0

Errors

if { [ catch {command_name...} ] } {
   # Handle error
}

Version History

2021