Resolved Issues: 2021

The following issues were resolved for the 2021 releases.

Resolved Issues: 2021.0.1

  • Updated the plot range fitting behavior so that it will exclude curves whose appearance has been hidden by using the clickable legend. [IM-3654].
  • Fixed the browser in the Plot Manager so that it once again displays information in parentheses for joints, actuators, and motors, which had been missing from the 2021 release. [IM-3665]
  • Updated motion animation file handling to allow generation of the .h3d file even in the case of analysis failure or when manually stopping the motion analysis before it has reached the specified end time. [IM-3666]
  • Re-established the default value for penetration depth in motion contacts to be 0.1 mm, bringing it back to the value used previously in 2019.1 and earlier releases. [IM-3668]
  • Updated the behavior of Reset > Visible Defaults on the motion contacts microdialog so that it does not alter values that are not currently being shown on the screen. [IM-3672]
  • Fixed the Export Image feature in the Profile Editor so that it works as intended again. [IM-3714]
  • Corrected entries in the Plot Manager browser to better handle the case when objects share the exact same name (are not unique). [IM-3724]
  • Fixed a traceback error seen in motion contact models when specifying HM as the SkinMesherMV setting via the devPreference.xml file. [IM-3592]
  • Fixed traceback error seen when entering the Joints tool for reported use case. [IM-3679]
  • Fixed an error that mistakenly caused the Intersecting Parts Found in Model warning to appear and to subsequently prevent Analyze Part workflows from proceeding forward. [IN-23666]
  • Fixed an issue where models created in Inspire 2021 that had parts or assemblies deleted or imported in between runs could not be reopened. [IN-23961]
  • Fixed an issue where the Convert to Mass feature was not giving the correct answer because the mass moment of inertia value was not being converted with the mass. [IN-23718]
  • Fixed an issue with incorrect thickness when running a reanalysis after gauge optimization. [IN-23592]
  • Fixed an issue where STL instances did not work correctly after using the Section Cut tool. [IN-23534]

Resolved Issues: 2021

  • Added a check box to refresh query results with the latest working revision when opening files from a PDM system. [IN-18710]
  • Added the ability to generate a run time .stmod file with no results from SimSolid runs. [IN-21520]
  • Added the ability to connect point masses to multiple surfaces for SimSolid analysis. [IN-22288]
  • Inspire now supports newer versions of NX through version 1934. [IN-22244]
  • Fixed an issue where Inspire failed to retain user preference settings. [IN-17594]
  • Fixed a crash when moving PolyNURBS cage points. [IN-22410]
  • Fixed an issue where old supports were not removed after push/pulling and moving a model. [INP-1029]
  • Fixed an issue where users could not view pure thermal results after viewing thermo-mechanical results. [INP-963]
  • Implemented status bar messaging for MDL export operation. [IM-513]
  • Corrected length of pin joints, which was previously coming up short when used in yoke applications. [IM-549]
  • Fixed misplaced leader line seen for some joint callout plots. [IM-807]
  • Removed an unexpected warning that was written to run.log file for models with acceleration actuators or motors. [IM-2917]
  • Introduced new cursor badge in motion plotting to indicate when a double-click action will create a pop-out plot instead of performing the usual fit operation. [IM-2922]
  • Changed border color to blue for data points viewed in the Profile Editor for table profile curves. [IM-3276]
  • Improved the usability of the Plot Manager by allowing a single click on .csv data at top level to automatically plot all components underneath without requiring individual component selection. [IM-3577]
  • Fixed placement of torsion spring dampers to be on the end of pin joints for the clevis use case. [IM-3375]
  • Fixed a traceback error that could be seen after a part that was attached to a concentrated mass or another part using connectors. [IM-3559]
  • Corrected a traceback error encountered when running a coupler model after a part replace operation. [IM-3365]
  • Removed a bottleneck in motion animation that was making playback slower than expected in release versions after 2019.3. [IM-3380]
  • Fixed orientation problems affecting the model configuration of structures forces. This was seen when using the Make Current Frame the New Design Position button. [IM-3425]
  • Changed the default location of the Create button for the Rigid Groups tool so that it is near the first part selected. It is now less likely to appear at the window border or to keep shifting as parts are selected. [IM-3449]
  • Deprecated the MDL export option, "MotionView 2019 or older mdl file (*.mdl)". [IM-3454]
  • Changed data entry for the Phase Shift parameter on the Oscillating profile to disallow entry of negative values. [IM-3464]
  • Fixed a traceback error that was seen when using a drag-and-drop operation to open .stmod files. [IM-3467]
  • Improved plot fitting operations to do a better job including peaks seen when running with freeze plots and the Show During Analysis option. [IM-3473]
  • Updated MDL export so that the part inertia is now a better match with what one sees from the Property Editor inside Inspire. [IM-3479]
  • Updated the Ground tool so that tooltips are shown when hovering over parts. [IM-3513]
  • Simplified selection behavior of motion contact glyphs so that two-step selections are not required for editing. [IM-3514]
  • Fixed the page count in the Plot Manager, which was not refreshing properly. [IM-3520]
  • Updated the Motion Contacts tool to ignore suppressed entities when in using the At Free Joints option. [IM-3542]
  • Fixed an issue where coil spring manipulators where seen to jump unpredictably when rotating the model after using panning operations. [IM-3545]
  • Fixed a traceback error that happened when exiting motion animation where many individual contact forces were being displayed with the Force Explorer. [IM-3557]
  • Updated the legend label text to be less verbose when plotting .csv data components. [IM-3569]
  • Improved speed of plotting motion results for multi-selections, which had slowed down when Undo was first introduced in the Plot Manager. [IM-3574]
  • Fixed the source of an application crash encountered when clicking on the Review button for error handling alert (m_error_37). [IM-3581]
  • Updated default ordering of entities in the Plot Manager browser. [IM-3594]
  • Fixed a solver calculation error seen in Friction Power plots that are available from motion contacts. [IM-3603]
  • Fixed an application crash that occurred when using the up/down keys while reviewing motion plots and changing cursor focus between the browser and a plot. [IM-3610]